Cooling Duty and Selection Basis
A wire rod air cooling system removes heat from hot rolled wire rod through controlled airflow across a cooling conveyor or fan bank. Fan selection must support cooling rate, distribution and the production-line operating range.
Selection focus: steel grade, rod diameter, line speed, inlet temperature, target cooling curve, conveyor width, active zones, plenum resistance, fan arrangement and redundancy.
Wire Rod Conveyor and Fan Bank
Product Route
Hot wire rod leaves rolling and moves across the cooling conveyor through active zones.
Air Route
Fan-bank or centralized supply air passes through plenums and outlets toward the rod. Zone control adjusts cooling intensity.
Fan layout and outlets must distribute air across conveyor width and along the intended cooling zones.
What a Wire Rod Air Cooling System Must Do
Remove heat at a controlled rate as wire rod travels across the conveyor. Air demand changes with grade, diameter, line speed and target properties. Fan quantity, spacing, plenum design, dampers and outlets determine distribution.
Remove Heat
Match airflow to product temperature, line speed and cooling target.
Distribute Air
Reduce variations across conveyor width and active zones.
Overcome Resistance
Maintain flow through ducts, headers, dampers and outlets.
Support Production Changes
Use zones, staged fans or speed control for different recipes.
Air Distribution Is as Important as Total Airflow
High total airflow cannot guarantee uniform cooling. Balance the plenum, fan spacing, dampers and outlet geometry so air reaches the rod.
Fan Spacing
Avoid dead zones and excessive overlap.
Plenum Design
Balance internal pressure across outlets.
Dampers and Zoning
Match active zones and production recipes.
Outlet Geometry
Nozzle size, angle and open area affect local air velocity.
Why Plenum, Duct and Nozzle Resistance Matter
Include inlet screens, ducts, plenums, dampers, headers, outlets and protective grilles. A direct axial fan bank may suit lower resistance, while centralized ducts and narrow outlets may require a higher-pressure direction.
Provide the airflow, air conditions and included boundaries for measured or supplier-reported losses. Count each loss once without adding full-path and component losses twice. Outlet velocity requirements differ from irreversible pressure losses; the system designer confirms the fan duty, active zones and air distribution.
Plenum / Header
Distribution loss
Nozzles / Outlets
Outlet condition
Duct Length
Friction loss
Dampers / Grilles
Control loss
Inlet Screens
Entry loss
Fan Banks, Centralized Air Supply and Zone Control
Arrangement depends on zone length, distribution, maintenance, redundancy and line controls.
Direct Fan Bank
Multiple axial fans under or beside the conveyor provide localized and independently controlled airflow.
Centralized Air Supply
Centrifugal fans feed common plenums or headers where greater volume and pressure are needed.
Zone and Speed Control
Staged operation, dampers or variable speed suit changing grade, diameter and line speed.
Wire Rod Cooling Fan Package for New Lines and Retrofits
Final supply scope depends on cooling-line arrangement, operating point, installation interface and agreement.
Cooling Fan / Fan Bank
Axial or centrifugal configuration against duty, zones and redundancy.
Motor and Drive
Power, voltage, frequency, protection, speed and drive against operating point.
Connections and Installation
Transitions, flexible joints, dampers, isolation and interfaces as specified.
Technical Documents
Selection report, curve, GA drawing and motor data as agreed.
Parameters Required for Wire Rod Cooling Fan Selection
Production and Cooling
- Steel grade and target cooling curve
- Rod diameter range
- Rolling and conveyor speed
- Rod inlet and target outlet temperature
- Conveyor width and active length
- Independent cooling zones
- Redundancy and operating schedule
Airflow and Installation
- Airflow per fan or zone
- Required static or total pressure
- Direct fan bank or centralized supply
- Plenum, header, duct and nozzle loss
- Ambient temperature and scale or dust
- Motor voltage, frequency, phase and protection
- Dimensions, quantity and control method
Wire Rod Cooling Fan Model Direction
The dedicated wire rod cooling fan is the primary entry. Alternatives require operating-point, distribution and resistance review.

Match the Fan to the Cooling Zone
Review the fan together with the conveyor, plenum and outlet distribution to define the required cooling duty.
Match the selected fan’s operating point and mounting interfaces to the actual zone. Keep the steel grade, rod diameter, line speed and target cooling curve tied to that same production case when comparing alternatives.
The dedicated product entry below leads to the published reference configuration. Do not copy its fan quantity or motor rating into a different line without a project-specific review.
Primary Product
Steel Mill Wire Rod Air Cooling Axial Flow FanPrimary product for conveyor or fan-bank controlled cooling where distribution and heat removal matter.
View primary product →Alternative Project Directions
Auxiliary localized axial airflow at confirmed installation.
View product →Large-volume centralized plenum with double-inlet centrifugal arrangement.
View product →Higher-pressure ducts, headers, dampers or nozzles.
View product →Higher-pressure process air at confirmed duty and motor load.
View product →New Cooling Lines and Existing Fan-Bank Upgrades
New Line
Coordinate fan quantity, zone length, plenum and control with the cooling curve and production mix.
- Product range and cooling targets
- Conveyor dimensions and zones
- Distribution and pressure calculation
- Control, maintenance and redundancy
Retrofit / Replacement
Start with the uneven-cooling diagnostic worksheet to compare zones under comparable production conditions before choosing a replacement.
Compare fan duty with plenum balance, blocked outlets, motor load, spacing and temperature distribution.
- Fan and motor nameplates
- Airflow, pressure, speed and power
- Cooling-zone and outlet arrangement
- Uneven temperature, low airflow, noise or vibration
FAQ About Steel Mill Wire Rod Air Cooling
What is a wire rod air cooling system?
A controlled air system that removes heat from hot rod after rolling. A fan bank or centralized supply distributes air across the conveyor.
Why is uniform distribution important?
Uneven flow creates different cooling rates across the width or along the coil. Plenum, spacing, dampers and outlets determine distribution.
How is cooling airflow determined?
Rod diameter, steel grade, line speed, inlet temperature, target cooling, conveyor width and active zones affect the demand.
When is a higher-pressure fan needed?
Long ducts, headers, narrow nozzles, control dampers or resistant cooling modules may raise pressure demand.
What data helps replace an existing cooling fan?
Send nameplates, airflow, pressure, speed, power, dimensions, cooling-zone layout and the current problem.
What can QIYUE FAN supply?
Depending on agreed scope, fan-side equipment, motor, connection items and documents such as selection report, performance curve and GA drawing.
Which model is the primary direction?
The dedicated wire rod cooling axial fan. GD30K2-12, 4-2×72, 9-19 and 9-26 are alternatives after duty and distribution confirmation.
Send Your Wire Rod Cooling Parameters
Steel grade, rod diameter, line speed, inlet and target temperature, cooling zones, airflow, pressure, voltage and quantity. For an existing line, attach the cooling-zone layout and a measured temperature profile if available.
