Industrial Fan Manufacturing · Zibo, China
QIYUE FAN industrial fan manufacturer
Menu
QIYUE FAN · INDUSTRIAL APPLICATIONS

Steel Mill Wire Rod Air Cooling System

Steel rolling & controlled process cooling

Cooling Duty and Selection Basis

A wire rod air cooling system removes heat from hot rolled wire rod through controlled airflow across a cooling conveyor or fan bank. Fan selection must support cooling rate, distribution and the production-line operating range.

Selection focus: steel grade, rod diameter, line speed, inlet temperature, target cooling curve, conveyor width, active zones, plenum resistance, fan arrangement and redundancy.

Cooling route

Wire Rod Conveyor and Fan Bank

Product Route

Hot wire rod leaves rolling and moves across the cooling conveyor through active zones.

Air Route

Fan-bank or centralized supply air passes through plenums and outlets toward the rod. Zone control adjusts cooling intensity.

Fan layout and outlets must distribute air across conveyor width and along the intended cooling zones.

System overview

What a Wire Rod Air Cooling System Must Do

Remove heat at a controlled rate as wire rod travels across the conveyor. Air demand changes with grade, diameter, line speed and target properties. Fan quantity, spacing, plenum design, dampers and outlets determine distribution.

Remove Heat

Match airflow to product temperature, line speed and cooling target.

Distribute Air

Reduce variations across conveyor width and active zones.

Overcome Resistance

Maintain flow through ducts, headers, dampers and outlets.

Support Production Changes

Use zones, staged fans or speed control for different recipes.

Cooling uniformity

Air Distribution Is as Important as Total Airflow

High total airflow cannot guarantee uniform cooling. Balance the plenum, fan spacing, dampers and outlet geometry so air reaches the rod.

Fan Spacing

Avoid dead zones and excessive overlap.

Plenum Design

Balance internal pressure across outlets.

Dampers and Zoning

Match active zones and production recipes.

Outlet Geometry

Nozzle size, angle and open area affect local air velocity.

Pressure selection

Why Plenum, Duct and Nozzle Resistance Matter

Include inlet screens, ducts, plenums, dampers, headers, outlets and protective grilles. A direct axial fan bank may suit lower resistance, while centralized ducts and narrow outlets may require a higher-pressure direction.

Fan pressure and cooling airflow: define the fan inlet/outlet boundaries and required flow for each active cooling zone. Account for inlet, duct, plenum, damper and outlet losses and the agreed allowance on a consistent static or total pressure basis.

Provide the airflow, air conditions and included boundaries for measured or supplier-reported losses. Count each loss once without adding full-path and component losses twice. Outlet velocity requirements differ from irreversible pressure losses; the system designer confirms the fan duty, active zones and air distribution.

Plenum / Header

Distribution loss

Nozzles / Outlets

Outlet condition

Duct Length

Friction loss

Dampers / Grilles

Control loss

Inlet Screens

Entry loss

Operating strategy

Fan Banks, Centralized Air Supply and Zone Control

Arrangement depends on zone length, distribution, maintenance, redundancy and line controls.

Direct Fan Bank

Multiple axial fans under or beside the conveyor provide localized and independently controlled airflow.

Centralized Air Supply

Centrifugal fans feed common plenums or headers where greater volume and pressure are needed.

Zone and Speed Control

Staged operation, dampers or variable speed suit changing grade, diameter and line speed.

Fan-side scope

Wire Rod Cooling Fan Package for New Lines and Retrofits

Final supply scope depends on cooling-line arrangement, operating point, installation interface and agreement.

Cooling Fan / Fan Bank

Axial or centrifugal configuration against duty, zones and redundancy.

Motor and Drive

Power, voltage, frequency, protection, speed and drive against operating point.

Connections and Installation

Transitions, flexible joints, dampers, isolation and interfaces as specified.

Technical Documents

Selection report, curve, GA drawing and motor data as agreed.

Selection input

Parameters Required for Wire Rod Cooling Fan Selection

Production and Cooling

  • Steel grade and target cooling curve
  • Rod diameter range
  • Rolling and conveyor speed
  • Rod inlet and target outlet temperature
  • Conveyor width and active length
  • Independent cooling zones
  • Redundancy and operating schedule

Airflow and Installation

  • Airflow per fan or zone
  • Required static or total pressure
  • Direct fan bank or centralized supply
  • Plenum, header, duct and nozzle loss
  • Ambient temperature and scale or dust
  • Motor voltage, frequency, phase and protection
  • Dimensions, quantity and control method
Direct product entry

Wire Rod Cooling Fan Model Direction

The dedicated wire rod cooling fan is the primary entry. Alternatives require operating-point, distribution and resistance review.

Red QIYUE wire rod cooling axial fan product reference with cylindrical housing and support frame
QIYUE fan for wire-rod air-cooling applications.

Match the Fan to the Cooling Zone

Review the fan together with the conveyor, plenum and outlet distribution to define the required cooling duty.

Match the selected fan’s operating point and mounting interfaces to the actual zone. Keep the steel grade, rod diameter, line speed and target cooling curve tied to that same production case when comparing alternatives.

The dedicated product entry below leads to the published reference configuration. Do not copy its fan quantity or motor rating into a different line without a project-specific review.

Primary Product

Steel Mill Wire Rod Air Cooling Axial Flow Fan

Primary product for conveyor or fan-bank controlled cooling where distribution and heat removal matter.

View primary product →

Alternative Project Directions

GD30K2-12

Auxiliary localized axial airflow at confirmed installation.

View product →
4-2×72

Large-volume centralized plenum with double-inlet centrifugal arrangement.

View product →
9-19

Higher-pressure ducts, headers, dampers or nozzles.

View product →
9-26

Higher-pressure process air at confirmed duty and motor load.

View product →
Project type

New Cooling Lines and Existing Fan-Bank Upgrades

New Line

Coordinate fan quantity, zone length, plenum and control with the cooling curve and production mix.

  • Product range and cooling targets
  • Conveyor dimensions and zones
  • Distribution and pressure calculation
  • Control, maintenance and redundancy

Retrofit / Replacement

Start with the uneven-cooling diagnostic worksheet to compare zones under comparable production conditions before choosing a replacement.

Compare fan duty with plenum balance, blocked outlets, motor load, spacing and temperature distribution.

  • Fan and motor nameplates
  • Airflow, pressure, speed and power
  • Cooling-zone and outlet arrangement
  • Uneven temperature, low airflow, noise or vibration
Technical questions

FAQ About Steel Mill Wire Rod Air Cooling

What is a wire rod air cooling system?

A controlled air system that removes heat from hot rod after rolling. A fan bank or centralized supply distributes air across the conveyor.

Why is uniform distribution important?

Uneven flow creates different cooling rates across the width or along the coil. Plenum, spacing, dampers and outlets determine distribution.

How is cooling airflow determined?

Rod diameter, steel grade, line speed, inlet temperature, target cooling, conveyor width and active zones affect the demand.

When is a higher-pressure fan needed?

Long ducts, headers, narrow nozzles, control dampers or resistant cooling modules may raise pressure demand.

What data helps replace an existing cooling fan?

Send nameplates, airflow, pressure, speed, power, dimensions, cooling-zone layout and the current problem.

What can QIYUE FAN supply?

Depending on agreed scope, fan-side equipment, motor, connection items and documents such as selection report, performance curve and GA drawing.

Which model is the primary direction?

The dedicated wire rod cooling axial fan. GD30K2-12, 4-2×72, 9-19 and 9-26 are alternatives after duty and distribution confirmation.

Send Your Wire Rod Cooling Parameters

Steel grade, rod diameter, line speed, inlet and target temperature, cooling zones, airflow, pressure, voltage and quantity. For an existing line, attach the cooling-zone layout and a measured temperature profile if available.

SEND COOLING LINE DATA →